CM-T3517: WinCE: Getting Started - Revision history

Nadav: /* Creating a bootable SD card */

2011-04-03T12:17:57Z

‎Creating a bootable SD card

Nadav: /* Installing the demo runtime image */

2010-12-19T07:09:14Z

‎Installing the demo runtime image

Nadav: New page: == Connecting the module == The following picture shows the recommended evaluation kit setup :- Image:CM T35 Properly Connected Image.jpg == Creating a bootable SD card == * Download ...

2010-12-15T09:59:14Z

New page: == Connecting the module == The following picture shows the recommended evaluation kit setup :- Image:CM T35 Properly Connected Image.jpg == Creating a bootable SD card == * Download ...

New page

== Connecting the module ==
The following picture shows the recommended evaluation kit setup
:- [[Image:CM T35 Properly Connected Image.jpg]]

== Creating a bootable SD card ==
* Download the latest [http://compulab.co.il/t3517/download/t3517-wince6-img.zip WinCE 6.0 runtime image for CM-T3517] and unzip the file.
* Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM.
: Follow the steps below:
# Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM-T3530 evaluation kit).
# Launch the TI_SDCard_boot utility (located in the {{filename|Utils}} folder).
# Choose the drive letter of the SD reader. [[Image:Format SD card step 1.jpg|350px]] 
# Select the {{filename|MLO}} file from the LiveDisk folder. [[Image:Format SD card step 2.jpg|350px]] 
# Select the rest of the files in the LiveDisk folder. [[Image:Format SD card step 3.jpg|350px]] 
# Select the {{parameter|FAT 32}} filesystem and {{parameter|4096 bytes}} allocation unit size in the {{cmd|Format Removable Disk}} pop-up and start the SD card format process. [[Image:Format SD card step 4.jpg|200px]] 
# After the formatting is complete, the utility automatically starts to copy the files to the SD card.
# Wait for the "Copying files done" message to appear in the debug output box. [[Image:Format SD card step 5.jpg|350px]] 
# Your SD card is now ready to boot the CM-T3530.

== Installing the demo runtime image ==
* Insert the bootable SD card into the SD socket (connector P13 on SB-T35).
* Configure the CM-T3513 for SD-Boot mode. There are two ways to do it:
** Preferred way: Hold the “SD BOOT” button while booting the device. You should hold the button until the synthetic splash-screen (4 colored squares) appears.
** Installing jumper E6.
* Power on the device. The synthetic splash-screen (4 colored squares) will appear on LCD display within a few seconds.
* An Updater image (dedicated WinCE image) is loaded from the SD-Card. Updater image boot time is approximately 50 seconds.
* The Updater utility will start automatically. The utility will install the runtime image onto the CM-T3517 NAND flash.
:[[Image:CM_T35_Updater_Running.jpg|400px]]
* The following message box informs you that the process is complete.
:[[Image:CM_T35_Updater_Complete.jpg|400px]]
* Make sure jumper E6 is removed. Otherwise, the installation process will be repeated next time you boot the device.
* Use the reset button to reboot the device.
* CompuLab WinCE demo image will be loaded from the NAND flash.

{{Note |Please refer to [[CM-T3530: WinCE: Updater| CM-T3530 Updater Guide]] for the technical installation process details}}

== See also ==
*[http://wiki.omap.com/index.php/SD/MMC_format_for_OMAP3_boot SD/MMC format for OMAP3 boot]
*[[CM-T3530: WinCE: Updater]]

[[Category:Windows CE|Getting Started]]
[[Category:CM-T3517|WinCE: Getting Started]]

@@ Line 4: / Line 4: @@
 == Creating a bootable SD card ==
 * Download the latest [http://compulab.co.il/t3517/download/t3517-wince6-img.zip WinCE 6.0 runtime image for CM-T3517] and unzip the file.
 * Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM.

@@ Line 7: / Line 7: @@
 * Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM.
 : Follow the steps below:
-# Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM-T3530 evaluation kit).
+# Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM-T3517 evaluation kit).
 # Launch the TI_SDCard_boot utility (located in the {{filename|Utils}} folder).
 # Choose the drive letter of the SD reader. <br> [[Image:Format SD card step 1.jpg|350px]]<br>
@@ Line 15: / Line 15: @@
 # After the formatting is complete, the utility automatically starts to copy the files to the SD card.
 # Wait for the "Copying files done" message to appear in the debug output box. <br>[[Image:Format SD card step 5.jpg|350px]]<br>
-# Your SD card is now ready to boot the CM-T3530.
+# Your SD card is now ready to boot the CM-T3517.
 == Installing the demo runtime image ==
 * Insert the bootable SD card into the SD socket (connector P13 on SB-T35).
-* Configure the CM-T3513 for SD-Boot mode. There are two ways to do it:
+* Configure the CM-T3517 for SD-Boot mode. There are two ways to do it:
 ** Preferred way: Hold the “SD BOOT” button while booting the device. You should hold the button until the synthetic splash-screen (4 colored squares) appears.
-** Installing jumper E6.
+** Install jumper E6.
-* Power on the device. The synthetic splash-screen (4 colored squares) will appear on LCD display within a few seconds.
+* Power on the device. The synthetic splash-screen (4 colored squares) will appear on the LCD display within a few seconds.
 * An Updater image (dedicated WinCE image) is loaded from the SD-Card. Updater image boot time is approximately 50 seconds.
 * The Updater utility will start automatically. The utility will install the runtime image onto the CM-T3517 NAND flash.