Nadav: New page: == Connecting the module == The following picture shows the recommended evaluation kit setup :- Image:CM T35 Properly Connected Image.jpg == Creating a bootable SD card == {{Note | Th...

2014-11-05T10:02:35Z

New page: == Connecting the module == The following picture shows the recommended evaluation kit setup :- Image:CM T35 Properly Connected Image.jpg == Creating a bootable SD card == {{Note | Th...

New page

== Connecting the module ==
The following picture shows the recommended evaluation kit setup
:- [[Image:CM T35 Properly Connected Image.jpg]]

== Creating a bootable SD card ==
{{Note | The TI SDCard boot utility does not work well on computers running Windows 7, use Windows XP (WinXP mode in Windows 7 works fine too.)}}
* Download the latest [http://compulab.co.il/t3530/download/t3530-wince7-img.zip WEC 7.0 runtime image for CM-T3530] and unzip the file.
* Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM.
: Follow the steps below:
# Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM-T3530 evaluation kit).
# Launch the TI_SDCard_boot utility (located in the {{filename|Utils}} folder).
# Choose the drive letter of the SD reader. [[Image:Format SD card step 1.jpg|350px]] 
# Select the {{filename|MLO}} file from the LiveDisk folder. [[Image:Format SD card step 2.jpg|350px]] 
# Select the rest of the files in the LiveDisk folder. [[Image:Format SD card step 3.jpg|350px]] 
# Select the {{parameter|FAT 32}} filesystem and {{parameter|4096 bytes}} allocation unit size in the {{cmd|Format Removable Disk}} pop-up and start the SD card format process. [[Image:Format SD card step 4.jpg|200px]] 
# After the formatting is complete, the utility automatically starts to copy the files to the SD card.
# Wait for the "Copying files done" message to appear in the debug output box. [[Image:Format SD card step 5.jpg|350px]] 
# Your SD card is now ready to boot the CM-T3530.

== Installing the demo runtime image ==
* Insert the bootable SD card into the SD socket (connector P13 on SB-T35).
* Configure the CM-T3530 for SD-Boot mode. There are two ways to do it:
** Preferred way: Hold the “SD BOOT” button while booting the device. You should hold the button until the synthetic splash-screen (4 colored squares) appears.
** Installing jumper E6.
* Power on the device. The synthetic splash-screen (4 colored squares) will appear on LCD display within a few seconds.
* An Updater image (dedicated WinCE image) is loaded from the SD-Card. Updater image boot time is approximately 50 seconds.
* The Updater utility will start automatically. The utility will install the runtime image onto the CM-T3530 NAND flash.
:[[Image:CM_T35_Updater_Running.jpg|400px]]
* The following message box informs you that the process is complete.
:[[Image:CM_T35_Updater_Complete.jpg|400px]]
* Make sure jumper E6 is removed. Otherwise, the installation process will be repeated next time you boot the device.
* Use the reset button to reboot the device.
* CompuLab WinCE demo image will be loaded from the NAND flash.

{{Note |Please refer to [[CM-T3530: WinCE: Updater| CM-T3530 Updater Guide]] for the technical installation process details}}

== See also ==
*[http://wiki.omap.com/index.php/SD/MMC_format_for_OMAP3_boot SD/MMC format for OMAP3 boot]
*[[CM-T3530: WinCE: Updater]]

[[Category:WEC7|Getting Started]]
[[Category:CM-T3530|WEC7: Getting Started]]

CM-T3530: WEC7: Getting Started - Revision history

Nadav: New page: == Connecting the module == The following picture shows the recommended evaluation kit setup :- Image:CM T35 Properly Connected Image.jpg == Creating a bootable SD card == {{Note | Th...