CM-T43: Evaluation Kit: Getting Started - Revision history

Grinberg at 12:30, 12 August 2016

2016-08-12T12:30:56Z

Alexm: /* System setup */

2016-05-11T08:57:32Z

‎System setup

Grinberg at 15:51, 8 May 2016

2016-05-08T15:51:23Z

Grinberg at 15:14, 1 May 2016

2016-05-01T15:14:29Z

Grinberg at 14:08, 1 May 2016

2016-05-01T14:08:37Z

Grinberg at 13:44, 1 May 2016

2016-05-01T13:44:57Z

Grinberg at 13:38, 1 May 2016

2016-05-01T13:38:29Z

Grinberg at 13:09, 1 May 2016

2016-05-01T13:09:46Z

Grinberg at 10:20, 1 May 2016

2016-05-01T10:20:58Z

New page

[[Image:CM-T43-eval-kit-quick-setup.jpg|800px]]
[[Image:SB_SOM_topview2.jpg|thumb|right|alt=SB-SOM top view|<div align="center">SB-SOM top view</div>]]
[[Image:SB_SOM_bottomview2.jpg|thumb|right|alt=SB-SOM bottom view|<div align="center">SB-SOM bottom view</div>]]

= System setup =
CM-T43 evaluation kit contains an SD card preloaded with [[CM-T43: Linux: Debian|Debian Linux image for CM-T43]].
# Insert the evaluation kit SD card into the SD/MMC/SDIO socket  '''P9''' until you hear a clicking sound.
# Make sure jumpers  '''E3''' and  '''E1''' are not populated (default state).
# Connect the standard USB cable (included) between your host PC and the evaluation kit micro-USB2.0 connector  '''P7'''.
# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings: 115200 baud rate, 8 data bits, 1 stop bit, no parity, no flow control.

= Starting the system =
# Connect the DC 12V power supply adapter (included) to  '''J6'''.
# Follow the messages in your terminal emulator program until you see the linux login prompt.
# '''NOTE:''' in case no messages appear in your terminal emulation program, please refer to the detailed [[SB-SOM: HOWTO: USB Console|USB console]] guide.
# Use the credentials below to login.
:* username: root
:* password: 111111

= What Next? =
*[[CM-T43 TI AM437x Linux | CM-T43 Linux guide]]
*[[CM-T43 Yocto Linux | CM-T43 Yocto guide]]
*[http://www.compulab.co.il/products/computer-on-modules/cm-t43/#devres CM-T43 development resources]


[[Category:SB-SOM]]
[[Category:CM-T43]]

@@ Line 1: / Line 1: @@
 [[Image:CM-T43-eval-kit-quick-setup.jpg|800px]]
 [[Image:SB_SOM_topview2.jpg|thumb|right|alt=SB-SOM top view|<div align="center">SB-SOM top view</div>]]
 [[Image:SB_SOM_bottomview2.jpg|thumb|right|alt=SB-SOM bottom view|<div align="center">SB-SOM bottom view</div>]]
-CM-T43 evaluation kit contains an SD card preloaded with [[CM-T43: Linux: Debian|Debian Linux image for CM-T43]].
+CM-T43 evaluation kit is preloaded with [[CM-T43: Linux: Debian|Debian Linux image for CM-T43]].
-# Insert the evaluation kit SD card into the SD/MMC/SDIO socket <!-- [[SB-SOM:_Connectors:_P9|P9]] --> '''P9''' until you hear a clicking sound.
+# Make sure jumpers '''E3''' and '''E1''' are not populated (default state).
 # Connect the standard USB cable (included) between your host PC and the evaluation kit micro-USB2.0 connector <!-- [[SB-SOM:_Connectors:_P7|P7]] --> '''P7'''.
 # On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
@@ Line 12: / Line 11: @@
 {{:SB-SOM: serial port parameters table}}
 </blockquote>
-= Starting the system =
+== Starting the system ==
 # Connect the DC 12V power supply adapter (included) to <!-- [[SB-SOM:_Connectors:_J6_and_J8|main DC power connector - J6]] --> '''J6'''.
 # Follow the messages in your terminal emulator program until you see the linux login prompt.
@@ Line 21: / Line 21: @@
 :* password: 111111
-= What Next? =
+'''More Details:''' ''[[SB-SOM: Connectors: J6 and J8|Connector J6]]''.
 *[[CM-T43 TI AM437x Linux|CM-T43 Linux guide]]
 *[[CM-T43 TI AM437x Yocto Linux|CM-T43 Yocto guide]]