Shai at 10:00, 8 March 2010

2010-03-08T10:00:35Z

Mike: 1 revision(s)

2010-02-25T14:19:48Z

1 revision(s)

Mike at 09:51, 22 February 2010

2010-02-22T09:51:04Z

New page

== Preparation steps ==
{{Note|Windows CE may be installed on CM-X300 using either a USB flash drive or a network connection. USB flash drive installation is the preferred method}}
* Obtain a PC workstation with a serial communication port.
* For networked installation, install a TFTP server on the host PC. For Windows machines we recommend using [http://tftpd32.jounin.net/ TFTPD32].
* Download the [http://compulab.co.il/x300/download/release/x300-wince6-img.zip Windows CE Demo package for CM-X300] from CompuLab website. Unzip the package to a directory on the host PC.
* All image files mentioned below can be found in the {{filename|ImageFiles}} folder.
* Copy the contents of folder corresponding to the CM-X300 hardware configuration to a USB flash drive or to the folder exported by the TFTP server.
** CPU stepping is identified according to the CM-X300 part number:
*:- C624 corresponds to PXA300
*:- C624'''M''' corresponds to PXA310

== Image installation ==
{{Warning|Do not reset or power off the CM-X300 during the installation process! Doing so may result in a disabled module! }}
* Connect the host PC to the CM-X300 via the serial cable supplied with the evaluation kit.
* Start a terminal emulation software on the host PC. Refer to [[CM-X300:_WinCE:_Setting_Up_a_Console|Setting up a console]] for settings.
* Turn on the CM-X300 system. The U-Boot (initial boot-loader) will start with a command prompt.
*: {{Note|If the boot settings of the CM-X300 are different from default, press and hold ^C while turning on the CM-X300 in order to get command prompt.}}

=== Installation with a USB flash drive ===
* Ensure that the files {{filename|wince_updater.nb0}}, {{filename|update.img}}, {{filename|nk.bin}}, {{filename|eboot.nb0}} and, optionally, {{filename|script.xml}} are present in the root directory of the USB flash drive.
* Connect the USB flash drive to USB2 (host/slave) port of the CM-X300 platform.
* Use the following U-Boot command to boot the Windows CE installer:
<pre>
> run ce_setup
</pre>
* Continue to [[CM-X300:_WinCE:_Getting_Started#Burning_the_image_to_NAND|Burning the image to NAND]] section

=== Installation with TFTP ===
* Connect CM-X300 Ethernet port to the local Ethernet network
* Ensure that the files {{filename|wince_updater.nb0}}, {{filename|update.img}}, {{filename|nk.bin}}, {{filename|eboot.nb0}} and, optionally, {{filename|script.xml}} are accessible by the TFTP server.
:- TFTPD32 users: copy the files mentioned above to a folder and point the TFTP server to that folder.
* Use U-Boot {{cmd|dhcp}} command to obtain an IP address or manually set the {{parameter|ipaddr}} environment variable:
<pre>
> setenv ipaddr <CM-X300 ip address>
</pre>
* Set the {{parameter|serverip}} environment variable and save the new environment to NAND flash:
<pre>
> setenv serverip <host ip address>
> saveenv
</pre>

* Use the following U-Boot command to boot the Windows CE installer:
<pre>
> tftp 80400000 update.img && autoscr 80400000
</pre>
* Continue to [[CM-X300:_WinCE:_Getting_Started#Burning_the_image_to_NAND|Burning the image to NAND]] section

=== Burning the image to NAND ===
* {{cmd|CM-X300 Updater}} application will be started automatically after Windows CE installer boot is complete. The following screen will be displayed:
*:- [[Image:X300-Updater-start-screen.jpg]]
* The CM-X300 Updater will point to the {{filename|\Hard Disk\NK.bin}} file, located on a USB flash disk.
* Uncheck the {{cmd|Quick Format}} check box to request a full low-level format of the CM-X300 NAND Flash.
*:- A full low level format of the NAND Flash takes several minutes
* Press the {{cmd|Start}} button
* The update process takes several minutes.
{|
|[[Image:X300-updater-Formatting.jpg]]
|[[Image:CM-X300 Updating.jpg]]
|}
* After the update is completed, the CM-X300 Updater will display the following notification.
*:- [[Image:X300-Updater-finished.jpg]]
* Press {{cmd|OK}}.

== Post Installation ==

* Windows CE boots automatically when the CM-X300 is power cycled or reset.
* The following screen appears when the CM-X300 is up and running:
*:- [[Image:CM-X300-Home-Screen.jpg]]

== See also ==

* [[CM-X300: WinCE: Configuring Eboot|Configuring Eboot]]
* [[WinCE: Application Development|Windows CE Application Development for CM-X300 modules]]
* [[CM-X300: WinCE6.0: Demo Image]]
* [[WinCE: OSDesign Development | Windows CE OSDesign Development]]
* [[U-Boot for CM-X300]]

[[Category:Windows CE|Getting Started]]
[[Category:CM-X300|Getting Started]]

@@ Line 72: / Line 72: @@
 * [[CM-X300: WinCE: Configuring Eboot|Configuring Eboot]]
 * [[WinCE: Application Development|Windows CE Application Development for CM-X300 modules]]
-* [[CM-X300: WinCE6.0: Demo Image]]
+* [[CM-X300: WinCE: Demo Image]]
 * [[WinCE: OSDesign Development | Windows CE OSDesign Development]]
 * [[U-Boot for CM-X300]]

← Older revision	Revision as of 14:19, 25 February 2010
(No difference)

CM-X300: WinCE: Getting Started - Revision history

Shai at 10:00, 8 March 2010

Mike: 1 revision(s)

Mike at 09:51, 22 February 2010