|
|
| (2 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| − | == Introduction ==
| + | {{:Transclusion: CL-SOM-iMX7: FreeRTOS: Running Demos}} |
| − | This article describes the process of loading FreeRTOS images into memory, and running the in-memory images. For quick evaluation, the FreeRTOS BSP for CL-SOM-iMX7 comes with precompiled images that can be found under the {{filename|images}} folder.
| |
| − | | |
| − | == Loading FreeRTOS into memory ==
| |
| − | A FreeRTOS image must be run from TCM, DDR, or OCRAM, depending on how it was built. Consult the following table for the right <'''load_addr'''> to use:
| |
| − | {| cellpadding="3" border="1" style="border: 1px solid rgb(85, 85, 85); border-collapse: collapse;"
| |
| − | |-
| |
| − | ! Image name
| |
| − | ! Must run from
| |
| − | ! load_addr
| |
| − | |-
| |
| − | | <image_name>.bin
| |
| − | | TCM
| |
| − | | 7F8000
| |
| − | |-
| |
| − | | <image_name>_ocram.bin
| |
| − | | OCRAM
| |
| − | | 910000
| |
| − | |-
| |
| − | | <image_name>_ddr.bin
| |
| − | | DDR
| |
| − | | 9FF00000
| |
| − | |}
| |
| − | | |
| − | === Loading from USB ===
| |
| − | * Power on the module and stop U-Boot from booting Linux by holding Ctrl-c.
| |
| − | * Place image into USB drive, and insert the USB drive into the P6 or P26 USB connector.
| |
| − | * Load image into memory:
| |
| − | <pre>
| |
| − | CL-SOM-iMX7 # usb start
| |
| − | CL-SOM-iMX7 # load usb 0 <load_addr> <image_name>
| |
| − | </pre>
| |
| − | To boot the image, go to [[CL-SOM-iMX7: FreeRTOS: Demos#Booting FreeRTOS from memory | Booting FreeRTOS from memory]].
| |
| − | | |
| − | === Loading from MMC ===
| |
| − | * Power on the module and stop U-Boot from booting Linux by holding Ctrl-c.
| |
| − | * Place image into SD-card, and insert the SD-card into the P9 connector.
| |
| − | * Load image into memory:
| |
| − | <pre>
| |
| − | CL-SOM-iMX7 # mmc dev 0
| |
| − | CL-SOM-iMX7 # mmc rescan
| |
| − | CL-SOM-iMX7 # load mmc 0 <load_addr> <image_name>
| |
| − | </pre>
| |
| − | To boot the image, go to [[CL-SOM-iMX7: FreeRTOS: Demos#Booting FreeRTOS from memory | Booting FreeRTOS from memory]].
| |
| − | | |
| − | === Loading from TFTP ===
| |
| − | * Power on the module and stop U-Boot from booting Linux by holding Ctrl-c.
| |
| − | * Setup TFTP as described in the [[Linux: Setting up a development environment]] article, and place the image into the TFTP folder on your workstation.
| |
| − | * Connect CL-SOM-iMX7 to a network using connector P21.
| |
| − | * Load image into memory:
| |
| − | <pre>
| |
| − | CL-SOM-iMX7 # setenv autoload no
| |
| − | CL-SOM-iMX7 # dhcp
| |
| − | CL-SOM-iMX7 # setenv serverip <your_workstation_ip>
| |
| − | CL-SOM-iMX7 # tftp <load_addr> <image_name>
| |
| − | </pre>
| |
| − | To boot the image, go to [[CL-SOM-iMX7: FreeRTOS: Demos#Booting FreeRTOS from memory | Booting FreeRTOS from memory]].
| |
| − | | |
| − | == Booting FreeRTOS from memory ==
| |
| − | * Run the image using the following commands:
| |
| − | <pre>
| |
| − | CL-SOM-iMX7 # dcache flush
| |
| − | CL-SOM-iMX7 # bootaux <load_addr>
| |
| − | </pre>
| |
| | | | |
| | == See also == | | == See also == |
| | | | |
| | * [[CL-SOM-iMX7: FreeRTOS: Demos Usage Guide]] | | * [[CL-SOM-iMX7: FreeRTOS: Demos Usage Guide]] |
| − | * [[FreeRTOS: Introduction to FreeRTOS development]] | + | * [[CL-SOM-iMX7: FreeRTOS: Introduction to NXP FreeRTOS development|FreeRTOS: Introduction to NXP FreeRTOS development]] |
| | * [http://www.freertos.org/ FreeRTOS website] | | * [http://www.freertos.org/ FreeRTOS website] |
| | | | |
| | [[Category:FreeRTOS]] | | [[Category:FreeRTOS]] |
| | [[Category:CL-SOM-iMX7]] | | [[Category:CL-SOM-iMX7]] |
Introduction
This article describes the process of loading FreeRTOS images into memory, and running the in-memory images. For quick evaluation, the FreeRTOS BSP comes with precompiled images that can be found under the images folder.
Loading FreeRTOS into memory
A FreeRTOS image must be run from TCM, DDR, or OCRAM, depending on how it was built. Consult the following table for the right <load_addr> to use:
| Image name
|
Must run from
|
load_addr
|
| <image_name>.bin
|
TCM
|
7F8000
|
| <image_name>_ocram.bin
|
OCRAM
|
910000
|
| <image_name>_ddr.bin
|
DDR
|
9FF00000
|
- Power on the module and stop U-Boot from booting Linux by holding Ctrl-c.
- Place the demo image into USB drive or SD-card, and connect it into the evaluation board.
- Use the following U-Boot commands to load the demo image from USB storage:
CL-SOM-iMX7 # usb start
CL-SOM-iMX7 # load usb 0 <load_addr> <image_name>
- Use the following U-Boot commands to load the demo image from SD-card:
CL-SOM-iMX7 # mmc dev 0
CL-SOM-iMX7 # mmc rescan
CL-SOM-iMX7 # load mmc 0 <load_addr> <image_name>
Booting FreeRTOS from memory
- Run the image using the following commands:
CL-SOM-iMX7 # dcache flush
CL-SOM-iMX7 # bootaux <load_addr>
See also
