Difference between revisions of "SB-UCM-iMX8: HOWTO: USB Console"
imported>Kirill.kapranov (→Setting up your host PC) |
|||
| Line 3: | Line 3: | ||
== Setting up your host PC == | == Setting up your host PC == | ||
| − | # | + | # Make sure that the micro-USB cable is properly connected between the SBC console connector to a USB port on your host PC. |
| − | # Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from | + | # Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from https://www.silabs.com/documents/public/software/CP210x_Windows_Drivers_with_Serial_Enumeration.zip |
| − | # Identify the host PC interface and port | + | # Identify the host PC interface and port number that will be used for communication with the SBC: |
| − | #* | + | #* In most Linux PCs, the serial port will be denoted as one of the following (where n is a positive integer): /dev/ttyUSB0, /dev/ttyUSB1 ... /dev/ttyUSBn |
| − | #* | + | #* In Windows PCs, the serial port usually will be denoted as one of the following (where n is a positive integer): COM1, COM2 ... COMn |
# Start a terminal emulation program (such as HyperTerminal on Windows or minicom on Linux). | # Start a terminal emulation program (such as HyperTerminal on Windows or minicom on Linux). | ||
# Within the terminal emulation program, in the serial port configuration section select the port identified in previous step and set the following serial port parameters: | # Within the terminal emulation program, in the serial port configuration section select the port identified in previous step and set the following serial port parameters: | ||
| Line 16: | Line 16: | ||
== Setting up the Compulab Board == | == Setting up the Compulab Board == | ||
| − | |||
# Start the system by enabling power through the main DC power connector. | # Start the system by enabling power through the main DC power connector. | ||
# Console messages should appear on your host PC through the terminal emulation program. | # Console messages should appear on your host PC through the terminal emulation program. | ||
| Line 22: | Line 21: | ||
<!--'''More Details:''' ''[[SB-iMX8:_Connector:J2|main DC power connector]]'', ''[[SB-SOM:_Jumpers:_E4|E4]]''.--> | <!--'''More Details:''' ''[[SB-iMX8:_Connector:J2|main DC power connector]]'', ''[[SB-SOM:_Jumpers:_E4|E4]]''.--> | ||
| − | [[Category: | + | [[Category:UCM-iMX93]] |
| + | [[Category:CL-SOM-iMX8Plus]] | ||
| + | [[Category:UCM-iMX8M-Plus]] | ||
| + | [[Category:UCM-iMX8M-Mini]] | ||
Latest revision as of 14:09, 23 July 2023
Setting up your host PC
- Make sure that the micro-USB cable is properly connected between the SBC console connector to a USB port on your host PC.
- Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from https://www.silabs.com/documents/public/software/CP210x_Windows_Drivers_with_Serial_Enumeration.zip
- Identify the host PC interface and port number that will be used for communication with the SBC:
- In most Linux PCs, the serial port will be denoted as one of the following (where n is a positive integer): /dev/ttyUSB0, /dev/ttyUSB1 ... /dev/ttyUSBn
- In Windows PCs, the serial port usually will be denoted as one of the following (where n is a positive integer): COM1, COM2 ... COMn
- Start a terminal emulation program (such as HyperTerminal on Windows or minicom on Linux).
- Within the terminal emulation program, in the serial port configuration section select the port identified in previous step and set the following serial port parameters:
Baud Rate Data Bits Stop Bits Parity Flow Control 115200 8 1 none none
Setting up the Compulab Board
- Start the system by enabling power through the main DC power connector.
- Console messages should appear on your host PC through the terminal emulation program.
