Difference between revisions of "CM-X300 U-Boot Update"

From Compulab Mediawiki
Jump to: navigation, search
m (1 revision(s))
 
(4 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
== CM-X300 Firmware Update process ==
+
#REDIRECT [[CM-X300: U-Boot: Firmware Update]]
−
 
 
−
=== Preliminary ===
 
−
Some basic steps are needed to be taken in order to update the CM-X300 firmware successfully:
 
−
* Make sure to power off the CM-X300 board
 
−
* Connect one end of the supplied serial cable to your module's base board and the other one to your host system
 
−
* Start terminal console application on your host system and configure the following:
 
−
** Set the serial port to one with the attached cable
 
−
** Set baud rate to 38400 bps
 
−
** 8 bit per frame
 
−
** 1 stop bit
 
−
** no parity
 
−
** no flow control
 
−
* Turn the CM-X300 board on
 
−
* Now you should get the U-Boot command prompt in your terminal application
 
−
{{Note| If you have an operating system installed or U-Boot environment configured for auto boot, you will have to stop the auto boot sequence by pressing any key in your terminal application during the start of the boot process!}}
 
−
U-Boot firmware could be updated either from [[U-Boot_for_CM-X300#USB_flash_drive|USB flash drive]] (with FAT filesystem), or from [[U-Boot_for_CM-X300#Network_tftp_download|Network tftp download]].
 
−
Either method is done from U-Boot command line.
 
−
 
 
−
=== USB flash drive ===
 
−
{{Note| Please, connect your flash drive directly to the base board of the module! Do not use any USB hubs or other separating equipment!}}
 
−
To update the U-Boot firmware via USB flash drive, follow the instructions precisely!
 
−
* Start the U-Boot USB subsystem and check that your storage device is ready and contains the firmware
 
−
** Type: ''usb start''
 
−
** Type: ''fatls usb 0'' to ensure you have the firmware in place
 
−
<pre>
 
−
U-Boot> usb start
 
−
(Re)start USB...
 
−
USB:   scanning bus for devices... 2 USB Device(s) found
 
−
      scanning bus for storage devices... 1 Storage Device(s) found
 
−
U-Boot> fatls usb 0
 
−
  524288  cm-x300-firmware
 
−
 
 
−
1 file(s), 0 dir(s)
 
−
</pre>
 
−
 
 
−
* Load the firmware to memory
 
−
** Type: ''fatload usb 0 80a00000 <firmware filename>''
 
−
 
 
−
<pre>
 
−
U-Boot> fatload usb 0 80a00000 cm-x300-firmware
 
−
reading cm-x300-firmware
 
−
 
 
−
524288 bytes read
 
−
</pre>
 
−
* Proceed to [[U-Boot_for_CM-X300#Update_process|Update process]] section
 
−
 
 
−
=== Network tftp download ===
 
−
In order to use this update method, you need:
 
−
* TFTP service/server installed on your host system
 
−
* Firmware file should reside in the root directory of TFTP service
 
−
To update the U-Boot firmware via tftp download, follow the instructions precisely!
 
−
* Download the firmware to module's memory
 
−
** Type: ''tftp 80a00000 <firmware filename>''
 
−
<pre>
 
−
U-Boot> tftp 80a00000 cm-x300-firmware
 
−
dm9000 i/o: 0x8000010, id: 0x90000a46
 
−
DM9000: running in 16 bit mode
 
−
MAC: 00:01:c0:05:20:be
 
−
operating at 100M full duplex mode
 
−
TFTP from server 10.1.1.13; our IP address is 10.1.1.144
 
−
Filename 'cm-x300-firmware'.
 
−
Load address: 0x80a00000
 
−
Loading: ####################################
 
−
done
 
−
Bytes transferred = 524288 (80000 hex)
 
−
</pre>
 
−
* Proceed to [[U-Boot_for_CM-X300#Update_process|Update process]] section
 
−
{{Note| If you get the "''could not establish link''" message, check that your ethernet plugs are in place and try again.}}
 
−
 
 
−
=== Update process ===
 
−
{{Warning| DO NOT RESET OR POWER OFF THE MODULE DURING THE UPDATE PROCESS! DOING SO MAY RESULT IN DISABLED MODULE!}}
 
−
 
 
−
* Flash the firmware to onboard NAND storage
 
−
** Type: ''nand erase 0 80000''
 
−
** Type: ''nand write 80a00000 0 80000''
 
−
<pre>
 
−
U-Boot> nand erase 0 80000
 
−
 
 
−
NAND erase: device 0 offset 0x0, size 0x80000
 
−
Erasing at 0x60000 -- 100% complete.
 
−
OK
 
−
U-Boot> nand write 80a00000 0 80000
 
−
 
 
−
NAND write: device 0 offset 0x0, size 0x80000
 
−
524288 bytes written: OK
 
−
</pre>
 
−
* Now you may reset the board
 
−
 
 
−
{{Important|In case you use Windows CE and you update U-Boot, you will need to load the ImageUdater after the U-Boot update. There is no need to install the image again. This will update the NAND flash metadata that is crucial for Windows CE.}}
 
−
 
 
−
== See also ==
 
−
 
 
−
* [[U-Boot quick reference]]
 
−
* [[Getting started with Linux on CM-X300]]
 
−
* [http://www.denx.de/wiki/U-Boot/Documentation U-Boot documentation]
 

Latest revision as of 15:26, 22 December 2009