Difference between revisions of "UCM-iMX8M-Plus: Evaluation Kit: Getting Started"
| Line 1: | Line 1: | ||
| − | [[Image:UCM- | + | [[Image:UCM-iMX8M-Plus-eval-kit-getting-started.png|frameless|top|1400px|link=]] |
== System setup == | == System setup == | ||
| − | UCM- | + | UCM-iMX8M-Plus evaluation kit is preloaded with UCM-iMX8M-Plus Yocto Linux image. |
| − | # Make sure | + | # Make sure jumper '''E5''' is populated (default state). |
| − | # Make sure | + | # Make sure jumper '''E3''' is removed (default state). |
| − | # | + | # Make sure that the main power switch SW1 is in the OFF position. |
| − | # Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector ''' | + | # For kits ordered with LCD panel: use the EB-HDRLVDS adapter to connect the LCD panel (if ordered with the kit) to connectors '''P13''' and '''P14'''. |
| + | # Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P3'''. | ||
# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings: | # On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings: | ||
<blockquote> | <blockquote> | ||
| Line 13: | Line 14: | ||
== Starting the system == | == Starting the system == | ||
| − | # Connect the DC 12V power supply adapter (included) to main DC power connector ''' | + | # Connect the DC 12V power supply adapter (included in the kit) to main DC power connector '''J1'''. |
| − | # Follow the messages in your terminal emulator program until you see the linux shell command line prompt. | + | # Toggle the main power switch '''SW1''' to '''ON''' position. |
| + | # Follow the messages in your terminal emulator program until you see the linux shell command line prompt. | ||
{{note|In case of no messages appear in your terminal emulation program, please refer to the detailed [[SB-UCM-iMX8: HOWTO: USB Console|USB console]] guide.}} | {{note|In case of no messages appear in your terminal emulation program, please refer to the detailed [[SB-UCM-iMX8: HOWTO: USB Console|USB console]] guide.}} | ||
| − | |||
== What Next? == | == What Next? == | ||
Latest revision as of 13:52, 5 August 2024
System setup
UCM-iMX8M-Plus evaluation kit is preloaded with UCM-iMX8M-Plus Yocto Linux image.
- Make sure jumper E5 is populated (default state).
- Make sure jumper E3 is removed (default state).
- Make sure that the main power switch SW1 is in the OFF position.
- For kits ordered with LCD panel: use the EB-HDRLVDS adapter to connect the LCD panel (if ordered with the kit) to connectors P13 and P14.
- Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector P3.
- On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
Baud Rate Data Bits Stop Bits Parity Flow Control 115200 8 1 none none
Starting the system
- Connect the DC 12V power supply adapter (included in the kit) to main DC power connector J1.
- Toggle the main power switch SW1 to ON position.
- Follow the messages in your terminal emulator program until you see the linux shell command line prompt.
|
In case of no messages appear in your terminal emulation program, please refer to the detailed USB console guide. |
