Difference between revisions of "CM-T3517: WinCE: Getting Started"
(New page: == Connecting the module == The following picture shows the recommended evaluation kit setup :- Image:CM T35 Properly Connected Image.jpg == Creating a bootable SD card == * Download ...) |
(→Installing the demo runtime image) |
||
| Line 7: | Line 7: | ||
* Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM. | * Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM. | ||
: Follow the steps below: | : Follow the steps below: | ||
| − | # Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM- | + | # Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM-T3517 evaluation kit). |
# Launch the TI_SDCard_boot utility (located in the {{filename|Utils}} folder). | # Launch the TI_SDCard_boot utility (located in the {{filename|Utils}} folder). | ||
# Choose the drive letter of the SD reader. <br> [[Image:Format SD card step 1.jpg|350px]]<br> | # Choose the drive letter of the SD reader. <br> [[Image:Format SD card step 1.jpg|350px]]<br> | ||
| Line 15: | Line 15: | ||
# After the formatting is complete, the utility automatically starts to copy the files to the SD card. | # After the formatting is complete, the utility automatically starts to copy the files to the SD card. | ||
# Wait for the "Copying files done" message to appear in the debug output box. <br>[[Image:Format SD card step 5.jpg|350px]]<br> | # Wait for the "Copying files done" message to appear in the debug output box. <br>[[Image:Format SD card step 5.jpg|350px]]<br> | ||
| − | # Your SD card is now ready to boot the CM- | + | # Your SD card is now ready to boot the CM-T3517. |
== Installing the demo runtime image == | == Installing the demo runtime image == | ||
* Insert the bootable SD card into the SD socket (connector P13 on SB-T35). | * Insert the bootable SD card into the SD socket (connector P13 on SB-T35). | ||
| − | * Configure the CM- | + | * Configure the CM-T3517 for SD-Boot mode. There are two ways to do it: |
** Preferred way: Hold the “SD BOOT” button while booting the device. You should hold the button until the synthetic splash-screen (4 colored squares) appears. | ** Preferred way: Hold the “SD BOOT” button while booting the device. You should hold the button until the synthetic splash-screen (4 colored squares) appears. | ||
| − | ** | + | ** Install jumper E6. |
| − | * Power on the device. The synthetic splash-screen (4 colored squares) will appear on LCD display within a few seconds. | + | * Power on the device. The synthetic splash-screen (4 colored squares) will appear on the LCD display within a few seconds. |
* An Updater image (dedicated WinCE image) is loaded from the SD-Card. Updater image boot time is approximately 50 seconds. | * An Updater image (dedicated WinCE image) is loaded from the SD-Card. Updater image boot time is approximately 50 seconds. | ||
* The Updater utility will start automatically. The utility will install the runtime image onto the CM-T3517 NAND flash. | * The Updater utility will start automatically. The utility will install the runtime image onto the CM-T3517 NAND flash. | ||
Revision as of 07:09, 19 December 2010
Contents
Connecting the module
The following picture shows the recommended evaluation kit setup
- -
Creating a bootable SD card
- Download the latest WinCE 6.0 runtime image for CM-T3517 and unzip the file.
- Use the TI_SDCard_boot_utility to create a disk with partition table geometry compatible with the OMAP3 boot ROM.
- Follow the steps below:
- Insert the SD card into an SD-Reader attached to the desktop computer (an SD-card is supplied with the CM-T3517 evaluation kit).
- Launch the TI_SDCard_boot utility (located in the Utils folder).
- Choose the drive letter of the SD reader.
- Select the MLO file from the LiveDisk folder.
- Select the rest of the files in the LiveDisk folder.
- Select the FAT 32 filesystem and 4096 bytes allocation unit size in the Format Removable Disk pop-up and start the SD card format process.
- After the formatting is complete, the utility automatically starts to copy the files to the SD card.
- Wait for the "Copying files done" message to appear in the debug output box.
- Your SD card is now ready to boot the CM-T3517.
Installing the demo runtime image
- Insert the bootable SD card into the SD socket (connector P13 on SB-T35).
- Configure the CM-T3517 for SD-Boot mode. There are two ways to do it:
- Preferred way: Hold the “SD BOOT” button while booting the device. You should hold the button until the synthetic splash-screen (4 colored squares) appears.
- Install jumper E6.
- Power on the device. The synthetic splash-screen (4 colored squares) will appear on the LCD display within a few seconds.
- An Updater image (dedicated WinCE image) is loaded from the SD-Card. Updater image boot time is approximately 50 seconds.
- The Updater utility will start automatically. The utility will install the runtime image onto the CM-T3517 NAND flash.
- The following message box informs you that the process is complete.
- Make sure jumper E6 is removed. Otherwise, the installation process will be repeated next time you boot the device.
- Use the reset button to reboot the device.
- CompuLab WinCE demo image will be loaded from the NAND flash.
|
Please refer to CM-T3530 Updater Guide for the technical installation process details |
