Difference between revisions of "SB-SOM: HOWTO: RS-232 Console"
| Line 1: | Line 1: | ||
[[Image:SB_SOM_topview2.jpg|thumb|right|alt=SB-SOM top view|<div align="center">SB-SOM top view</div>]] | [[Image:SB_SOM_topview2.jpg|thumb|right|alt=SB-SOM top view|<div align="center">SB-SOM top view</div>]] | ||
[[Image:SB_SOM_bottomview2.jpg|thumb|right|alt=SB-SOM bottom view|<div align="center">SB-SOM bottom view</div>]] | [[Image:SB_SOM_bottomview2.jpg|thumb|right|alt=SB-SOM bottom view|<div align="center">SB-SOM bottom view</div>]] | ||
| − | = Setting up your host PC = | + | == Setting up your host PC == |
| − | # Connect the RS-232 cable (included with the evaluation kit) between the SBC | + | # Connect the RS-232 cable (included with the evaluation kit) between the SBC connector '''P8''' and a free RS-232 port on your host PC. |
# Identify the host PC interface and port you will be using for communication with the SBC: | # Identify the host PC interface and port you will be using for communication with the SBC: | ||
#* For Linux hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): /dev/ttyS0, /dev/ttyS1 ... /dev/ttySn | #* For Linux hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): /dev/ttyS0, /dev/ttyS1 ... /dev/ttySn | ||
| Line 12: | Line 12: | ||
</blockquote> | </blockquote> | ||
| − | = Setting up the Compulab Board = | + | '''More Details:''' ''[[SB-SOM:_Connectors:_P8|connector P8]]''. |
| − | # Make sure | + | |
| − | # Start the system by enabling power through the | + | == Setting up the Compulab Board == |
| + | # Make sure '''DS3''' LED is '''OFF''' while '''DS2''' LED is '''ON'''. If this is not the case, populate jumper '''E3'''. | ||
| + | # Start the system by enabling power through the main DC power connector. | ||
# Console messages should appear on your host PC through the terminal emulation program. | # Console messages should appear on your host PC through the terminal emulation program. | ||
| + | |||
| + | '''More Details:''' ''[[SB-SOM:_Connectors:_J6_and_J8|main DC power connector]]''<!--, ''[[SB-SOM:_Jumpers:_E3|E3]]'', [[SB-SOM: LEDS: DS2 and DS3|DS3 LED]], [[SB-SOM: LEDS: DS2 and DS3|DS2 LED]]-->. | ||
[[Category:SB-SOM]] | [[Category:SB-SOM]] | ||
Latest revision as of 06:50, 25 May 2016
Setting up your host PC
- Connect the RS-232 cable (included with the evaluation kit) between the SBC connector P8 and a free RS-232 port on your host PC.
- Identify the host PC interface and port you will be using for communication with the SBC:
- For Linux hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): /dev/ttyS0, /dev/ttyS1 ... /dev/ttySn
- For Windows Hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): COM1, COM2 ... COMn
- Start a terminal emulation program (such as HyperTerminal on Windows or minicom on Linux).
- Within the terminal emulation program, in the serial port configuration section select the port identified in previous step and set the following serial port parameters:
Baud Rate Data Bits Stop Bits Parity Flow Control 115200 8 1 none none
More Details: connector P8.
Setting up the Compulab Board
- Make sure DS3 LED is OFF while DS2 LED is ON. If this is not the case, populate jumper E3.
- Start the system by enabling power through the main DC power connector.
- Console messages should appear on your host PC through the terminal emulation program.
More Details: main DC power connector.
