Device Tree

Available Device Tree Files

The current release includes the following dtb files:

DTB	Hardware Configuration and Features	Jumpers/Connectors Settings
sbc-mcm-imx93.dtb	default hardware configuration + lvds display	visit Connector Locations

Set device tree

The current release provides two methods to switch between dtb files:

U-Boot environment

The U-boot fdtfile variable contains the device tree name that will be loaded into the RAM. This variable can be changed by:

Environment	Command
U-Boot	setenv fdtfile <fdt_file_name>; saveenv;
Linux	fw_setenv fdtfile <fdt_file_name>

GRUB environment (if the image was created with the meta-compulab-uefi layer)

Environment	Command/Procedure
GRUB Boot Menu	Goto "Advanced Boot Options" and choose a device tree from the provided dtb list.
Linux	grub-editenv /boot/grub/grubenv set fdtfile=<fdt_file_name>

Serial Console

MCM-iMX93 provides serial console on UART1.
SBC-MCM93 carrier-board exposes the console UART via CP2104 serial-to-USB bridge on connector P3 depicted here

Connecting to a host PC

Use a micro-USB cable to connect the console to an USB port on your host PC.
Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from https://www.silabs.com/documents/public/software/CP210x_Windows_Drivers_with_Serial_Enumeration.zip
Identify the host PC interface and port number that will be used for communication with the MCM-iMX93 evaluation kit:
- In most Linux PCs, the serial port will be denoted as one of the following (where n is a positive integer): /dev/ttyUSB0, /dev/ttyUSB1 ... /dev/ttyUSBn
- In Windows PCs, the serial port usually will be denoted as one of the following (where n is a positive integer): COM1, COM2 ... COMn
Start a terminal emulation program (such as PuTTY on Windows or minicom on Linux).
In the port configuration section of the terminal emulation program select the port identified in previous step and set the following serial port parameters:

Baud Rate Data Bits Stop Bits Parity Flow Control

115200 8 1 none none

Display

LVDS

The MCM-iMX93 evaluation kit can be optionally supplied with the Startec KD070HDTLA020 7" LVDS LCD panel.
Use the EB-HDRLVDS adapter to connect the LCD panel (if ordered with the kit) to connectors P13 and P14 as depicted in Connector Locations . Check the Linux device node for information about the display, such as its supported modes and its current configuration.

udevadm info -ap /sys/class/drm/card0-LVDS-1

Display Manager

MCM-iMX93 Yocto uses Weston as the default display manager. It can be configured in /etc/xdg/weston/weston.ini.
For example the transform setting can be set to rotate-90, rotate-180, rotate-270, or commented out.
In order to apply the configuration, you need to:

systemctl restart weston

Audio

SBC-MCM93 features WM8926 audio codec.

List available sound cards

aplay

aplay -l

**** List of PLAYBACK Hardware Devices ****
card 0: wm8962audio [wm8962-audio], device 0: HiFi wm8962-0 [HiFi wm8962-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

procfs

cat /proc/asound/cards

 0 [wm8962audio    ]: fsl-asoc-card - wm8962-audio
                      wm8962-audio

Audio Playback

gplay-1.0 and aplay allow playback of media files:

gplay-1.0 /path/to/media.file
aplay -D hw:0,0 -vv /path/to/media.file

USB

MCM-iMX93 features two USB2.0 ports that are derived from the i.MX93 USB sub-system.
SBC-MCM93 carrier-board multiplexes J2 USB connector with mini-PCIe socket P8. To use USB connector J2 make sure jumper E1 is open.
USB connector J3 is multiplexed with USB SDP port as detailed here.

USB in device mode

USB port can be operated in device mode when connected to a host machine using connector P21.
Available gadgets for the UBS device mode:

USB gadget	SOM command
usb serial device	modprobe g_serial
usb network device	modprobe g_ether
usb mass storage device	modprobe g_mass_storage file=/dev/sdX

CAN bus

SBC-MCM93 evaluation board exposes one CAN bus interface on header P17.

To test it you will need another board with CAN IF
Configure both CAN interface bit-rate to 1 Mbit/sec:

 ip link set can0 up type can bitrate 1000000

On one system, dump all received data frames as well as error frames:

candump any,0:0,#FFFFFFFF

  can0  111   [8]  11 22 33 44 55 66 77 88
  can0  11111111   [8]  11 22 33 44 55 66 77 88
...
  can0  03FF0983   [8]  D7 61 FF 03 C1 F7 C1 34
  can0  19C34D32   [8]  F7 5A C2 73 AD 0E 3F 0B
  can0  0675E391   [4]  2B 2D D3 49
  can0  13091C55   [8]  99 32 EC 77 27 81 49 0B
  can0  098D67CF   [8]  22 50 AB 48 AD 7F F4 26
  can0  05263FEC   [5]  1B 4C 02 45 6E
  can0  12B30E20   [0] 
  can0  1F193DF9   [1]  C5
  can0  1EB0B18F   [8]  3E 3F DA 57 C2 FE 73 58
  can0  1E5C64D9   [5]  6F 0D B3 63 6A
  can0  1E1DE3F9   [8]  96 48 AC 79 4E 00 27 71
  can0  0E1A11B7   [8]  75 81 70 7C 86 79 A7 77
  can0  05F8FD8B   [7]  33 F9 9B 1E 77 3D 1F
  can0  1E155FCD   [8]  E6 BA F8 58 ED 6D C8 10
  can0  1D91DF9E   [8]  5D 29 82 7B 97 1D AB 5C
  can0  11FB3CDA   [3]  14 65 C3
  can0  091352C0   [2]  2C ED
...

On second system:

Send standard CAN frame:

cansend can0 111#1122334455667788

Send extended CAN frame:

cansend can0 11111111#1122334455667788

CAN frames (extended mode) generator, random payload, interval between two successive flames 50 msec:

cangen -g 50 -e -D r -v can0

can: raw protocol (rev 20170425)
...
  can0  03FF0983#D7.61.FF.03.C1.F7.C1.34
  can0  19C34D32#F7.5A.C2.73.AD.0E.3F.0B
  can0  0675E391#2B.2D.D3.49
  can0  13091C55#99.32.EC.77.27.81.49.0B
  can0  098D67CF#22.50.AB.48.AD.7F.F4.26
  can0  05263FEC#1B.4C.02.45.6E
  can0  12B30E20#
  can0  1F193DF9#C5
  can0  1EB0B18F#3E.3F.DA.57.C2.FE.73.58
  can0  1E5C64D9#6F.0D.B3.63.6A
  can0  1E1DE3F9#96.48.AC.79.4E.00.27.71
  can0  0E1A11B7#75.81.70.7C.86.79.A7.77
  can0  05F8FD8B#33.F9.9B.1E.77.3D.1F
  can0  1E155FCD#E6.BA.F8.58.ED.6D.C8.10
  can0  1D91DF9E#5D.29.82.7B.97.1D.AB.5C
  can0  11FB3CDA#14.65.C3
  can0  091352C0#2C.ED
...

Ethernet

SBC-MCM93 carrier-board features two Gigabit Ethernet ports implemented with two RTL8211FDI PHYs.
The NetworkManager can be used to manage these interfaces.

Bandwidth test example

Start iperf3 server on host:

iperf3 -s -i 60

Straight (client sends, server receives) 1 min. test with report each 10 sec.

iperf3 -t 60 -i 10

Reverse (server sends, client receives) test

iperf3 -t 60 -i 10 -R

WiFi

SBC-MCM93 carrier-board features 802.11ac wireless connectivity solution implemented with an NXP 88W8997 module.
The NetworkManager can be used to manage WiFi interface.

Before working with WiFi, please ensure that WiFi antenna is connected to the WiFi module.

Enable/Disable WiFi Interface

To enable WiFi interface:

nmcli radio wifi on

To disable WiFi interface:

nmcli radio wifi off

Network Scanning

Sample WiFi scanning:

nmcli dev wifi list

The output will show the list of Access Points and Ad-Hoc cells in range.

Connecting to Access Point

In the following example:

Replace <SSID> and <PASSWORD> with the actual access point parameters:

nmcli device wifi connect <SSID> password <PASSWORD> name WifiCon

Disconnect wireless network:

nmcli connection down WifiCon

Connect wireless network again:

nmcli connection up WifiCon

Creating Access Point

In the following example:

Replace <SSID> and <PASSWORD> with desired access point parameters:

nmcli device wifi hotspot ssid <SSID> password <PASSWORD> con-name HotspotCon

Disable wireless AP:

nmcli connection down HotspotCon

Enable wireless AP again:

nmcli connection up HotspotCon

Bluetooth

SBC-MCM93 carrier-board features Bluetooth connectivity implemented with an NXP 88W8997 module.

Before working with Bluetooth, please ensure that Bluetooth antenna is connected to the WiFi / Bluetooth.

To start bluetoothctl use the following command:

bluetoothctl

To start the scan process use the following commands:

 default-agent
 power on
 scan on

Bluetooth device should be turned on and visible. Its MAC-adress and name should appear in bluetoothctl in following format:

[CHG] Device AA:BB:CC:DD:EE:FF Name: Device_Name

To pair with the Bluetooth device use the following command:

pair AA:BB:CC:DD:EE:FF

Where AA:BB:CC:DD:EE:FF is MAC-adress of the Bluetooth device.

To quit bluetoothctl use the following command:

[Device_Name]# quit

Cellular Modem

The MCM-iMX93 evaluation kit can be optionally supplied with Quectel EG25-G mini-PCIe cellular modem

Install the modem module into the mini-PCIe socket P8
Close jumper E1
Connect a cellular antenna to modem's main antenna connector
Install an active SIM card into SIM socket P7
Boot to linux

Run the following command to verify that the modem is detected correctly:

lsusb

Expected output:

Bus 001 Device 002: ID 2c7c:0125 Quectel Wireless Solutions Co., Ltd. EC25 LTE modem

run:

mmcli -L

Expected output:

/org/freedesktop/ModemManager1/Modem/0 [QUALCOMM INCORPORATED] QUECTEL Mobile Broadband Module

Obtain <apn> of your sim card company ,e.g. rl.internet

Establish connection:

 nmcli connection add type gsm ifname '*' con-name CellularCon apn <apn>
 nmcli connection

Expected output:

NAME                UUID                                  TYPE      DEVICE   
CellularCon         a1620622-8588-4349-b3fc-66be79fbbede  gsm       cdc-wdm0

Allow up to a minute to connect to wireless network and make sure modem state is connected:

mmcli -m 0

To test the wireless interface run:

ping -c 5 dns.google -I wwan0

UART

The following table outlines default UART routing when MCM-iMX93 is used with the SBC-MCM93 carrier-board:

MCM-iMX93 port	Linux device	on SBC-MCM93 carrier-board	pinout
UART3	/dev/ttyLP2	100-mil header P20	2-rx, 4-tx
UART5	/dev/ttyLP4	100-mil header P19	4-tx, 2-rx, 3-rts, 6-cts

Example: testing UART5

Short RX and TX pins on SBC-MCM93 to create a loop-back.
Run the following commands:

stty -F /dev/ttyLP4 1:0:1cb2:0:3:1c:7f:15:4:5:1:0:11:13:1a:0:12:f:17:16:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0
cat /dev/ttyLP4 &
echo hello > /dev/ttyLP4

The "hello" string should appear on the terminal.

I2C

The following I2C buses and devices are present when MCM-iMX93 is used with the SBC-MCM93 carrier-board:

Device	I2C bus in Linux	Address	HW port in MCM-iMX93
user I2C on connector P16 pins: 3-sda, 5-scl	5	NA	I2C6

To list all mapped devices:

ls /proc/device-tree/soc@0/bus@*/i2c@*/*@* -d -w 1

Note how:

each node is appended with its address.
I2C buses order corresponds to the order of their addresses.

e.g. to inspect bus 0, in which we have RTC, run:

# i2cdetect -y 0
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:                         -- -- -- -- -- -- -- -- 
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
50: 50 51 52 53 -- -- -- -- -- -- -- -- -- -- -- -- 
60: -- -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- 
70: -- -- -- -- -- -- -- --

In the above output numbers mark unused devices, UU marks a device that is used by a driver.

Indeed we see RTC in use at offset 0x69.

An example how to dump EEPROM contents:

hexdump -C /sys/devices/platform/soc@0/44000000.bus/44340000.i2c/i2c-0/0-0050/eeprom

SPI

SBC-MCM93 carrier-board exposes SPI3 port on 10-mil header P15.

ECSPI3_MOSI - pin 3
ECSPI3_SCLK - pin 5
ECSPI3_MISO - pin 2
ECSPI3_SSO - pin 4

Loopback example:

Short MOSI and MISO pins.

Compile test tool:

${CROSS_COMPILE}gcc ./tools/spi/spidev_test.c -o ./spidev_test

Copy the spidev_test binary to the SoM.

On the module, run:

./spidev_test -v -D /dev/spidev0.0 -p "hello"

You should see RX same as TX.

GPIO

SBC-MCM93 carrier-board provides the following MCM-iMX93 GPIOs on 100-mil header P18.

Signal Name	pin	GPIO # in sysfs
GPIO_IO18	2	32+18
GPIO2_21	3	96+21
GPIO_IO24	5	32+24
GPIO_IO26	7	32+26
GPIO_IO22	9	32+22

Example: controlling pin GPIO_IO18

Exporting the pin in sysfs

cd /sys/class/gpio/
echo $((32+18)) > export

Now pin GPIO_IO18 is assigned to sysfs. You can view the newly created entry in line 18 by running:

gpioinfo 0

Writing to a pin

cd /sys/class/gpio/gpio$((32+18))

Set pin direction to output:

echo out > direction

Set pin value to high or low:

echo 1 > value 
echo 0 > value

Reading from a pin

cd /sys/class/gpio/gpio$((32+18))

Set pin direction to input:

echo in > direction

Read the value of the pin from the value file:

cat value

ADC

i.MX93 SoC features integrated 12 bit analog to digital converter.
To use the ADC, enable it in device tree e.g. in arch/arm64/boot/dts/compulab/sbc-mcm-imx93.dts:

&adc1 {
       vref-supply = <&reg_vref_1v8>;
       status = "okay";
};

Sysfs device controls will appear in:

cd /sys/bus/iio/devices/iio\:device0/

SBC-MCM93 exposes ADC signals on 100-mil header P9.

Signal Name	pin on P9	sysfs file
ADC_IN0	2	in_voltage0_raw
ADC_IN1	4	in_voltage1_raw
ADC_IN2	6	in_voltage2_raw
ADC_IN3	3	in_voltage3_raw

For example, to read voltage from P9-2 run:

cat /sys/bus/iio/devices/iio\:device0/in_voltage0_raw

Expected output is a value in range 0 - 4095 which spans over the voltage range 0 - 1.8V

Suspend / Resume

The following operation requires root access.

MCM-iMX93 features suspend mode, which allows to minimize power consumption.

The following command should be used to enter suspend mode:

echo mem >/sys/power/state

To resume normal operation press shortly the power button SW4.

CPU temperature

i.MX93 SoC features an internal temperature sensor which allows to measure the SoC temperature. Execute the following command to read the current CPU temperature:

cat /sys/class/thermal/thermal_zone0/temp

RTC

MCM-iMX93 features two RTC devices:

i.MX93 internal RTC (rtc0) - can be used as wake-up source
AB1805 external RTC (rtc1) - can be used for low current battery powered time keeper

Internal RTC - rtc0

System information:

Wake up:
rtc0 can be used as a wake up source, as a result an rtcwakeup can be used with this device:

rtcwake --device /dev/rtc0 -s 5 -m mem

External RTC - rtc1

Set the date and write it into the RTC:

date -s "16 Jun 2023 12:00:00"

Fri 16 Jun 2023 12:00:00
hwclock --systohc --rtc /dev/rtc1

Read the RTC time and date:

hwclock --show --rtc /dev/rtc1

2023-06-16 12:01:37.935876+00:00

Device Serial Number

Product information is stored in on-board EEPROM.

To read the product serial number run:

cat /proc/device-tree/product-sn && echo

To read the product configuration part number run:

cat /proc/device-tree/product-options && echo

MCM-iMX93: Yocto Linux: How-To Guide

Contents

Device Tree

Available Device Tree Files

Set device tree

Serial Console

Connecting to a host PC

Display

LVDS

Display Manager

Audio

List available sound cards

Audio Playback

USB

USB in device mode

CAN bus

Ethernet

Bandwidth test example

WiFi

Enable/Disable WiFi Interface

Network Scanning

Connecting to Access Point

Creating Access Point

Bluetooth

Cellular Modem

UART

I2C

SPI

GPIO

Example: controlling pin GPIO_IO18

ADC

Suspend / Resume

CPU temperature

RTC

Internal RTC - rtc0

External RTC - rtc1

Device Serial Number

See Also

Navigation menu

Search