CL-SOM-iMX8X: Evaluation Kit: Hardware Guide

From Compulab Mediawiki
Revision as of 07:38, 11 September 2019 by imported>Mykola.cherkunov
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Overview

Terms and Definitions

  • SoM – System-on-Module.
  • SBC – Single Board Computer.
  • Evaluation kit – A combination of CL-SOM-iMX8X SoM and SB-iMX8X carrier-board accompanied by a set of accessories. More information here.
  • CL-SOM-iMX8X– System-on-module product based on the iMX8X SoC. More information here.
  • SBC-iMX8X – A single board computer, which contains CL-SOM-iMX8X system-on-module and SB-iMX8X carrier-board. More information here.

Reference Carrier Board

  • All additional materials for CL-SOM-iMX8X are available here.
  • All additional materials for SBC-iMX8X are available here.

Additional resources

Getting started with CL-SOM-iMX8X evaluation kit.

Carrier Board

600px 600px

Interfaces and Functions

DC Power

SBC-iMX8X main power is provided with 12V DC power supply. Adapters for European AC and US AC outlets are included. Connect the power supply to connector J3 before turning on the device.

Serial Console

To start using serial console connect your host PC to the micro-USB connector P12 with the USB cable from the Evaluation kit.

USB

SBC-iMX8X features two USB2.0 ports available via dual USB connector U30.

Ethernet

SBC-iMX8X is equipped with two Ethernet ports via RJ45 connectors.

  • P2A – secondary Ethernet port.
  • P2B – primary Ethernet port.

PCI-Express

Mini-PCIe devices can be installed into the SBC-iMX8X mini-PCIe socket P11. Full / half size mini-PCIe modules are supported.
Jumper E15 must be installed for mini-PCIe operation.

CAN bus

Two independent CAN bus interfaces are available via headers P17 and P18.
To start using CAN bus the following jumpers should be installed:

  • P17 - E11 and E12
  • P18 - E13 and E14

Please refer to CL-SOM-iMX8X reference guide and SB-iMX8X schematics for details.

RS485

RS485 interface is available via connector P16.
Please refer to CL-SOM-iMX8X reference guide and SB-iMX8X schematics for details.

Wireless

WiFi/Bluetooth

For WiFi operation connect the WiFI/BT antenna (included in the evaluation kit) to CL-SOM-iMX8X connector ANT2.
For Bluetooth operation connect the WiFI/BT antenna (included in the evaluation kit) to CL-SOM-iMX8X connector ANT1.

Cellular

USB modems in mini-PCIe form-factor can be plugged into mini-PCIe socket P11. For modem operation:

  • Insert the cellular modem into socket P11.
  • Insert the SIM card to socket P10.

Display

HDMI

CL-SOM-iMX8X evaluation kit contains MIPI-to-HDMI adapter. To start using an HDMI monitor follow the next steps:

  • Install MIPI-to-HDMI adapter into socket P47.
  • Connect HDMI cable to connector J1.

MIPI-DSI

SBC-iMX8X is compatible with the KD050HDFIA LCD display panel.
To enable the display connect the data cable to connector P22.
To enable the touch-panel connect the touch-panel cable to connector P46

Camera

SBC-iMX8X is compatible with the LI-OVO5640-MIPI camera module.
To start using the camera connect the camera module to connector P8.

Multi-functional signals access

UART

UART interface is available via header P20.
Please refer to CL-SOM-iMX8X reference guide and SBS-MX8X schematics for details.

SPI

SPI interface is available via headers P20 and P21.
Please refer to CL-SOM-iMX8X reference guide and SBS-MX8X schematics for details.

I2C

I2C interface is available via header P20.
Please refer to CL-SOM-iMX8X reference guide and SBS-MX8X schematics for details.

GPIO

GPIO signals is available via headers P20 and P21.
Please refer to CL-SOM-iMX8X reference guide and SBS-MX8X schematics for details.

System

Reset

Pressing the reset button SW5 triggers SBC-iMX8X cold reset.

Boot Sequence Selection

Pressing and holding the alt-boot button SW6 during power-up or cold reset forces alternative boot sequence.

Power ON / OFF

Long press on the Power On button SW4 shuts down the device.

RTC

RTC is implemented on CL-SOM-iMX8X and receives the power from coin-cell battery BH1.

JTAG

JTAG interface is available via header P29.
Please refer to CL-SOM-iMX8X reference guide and SB-iMX8X schematics for details.

Jumpers Summary

Jumpers:

  • E1 - alternative boot.
  • E2 - EEPROM write protect.
  • E3 - force debug console over RS-232.
  • E4 - force UART3 to P12.
  • E5 - base EEPROM write protect.
  • E6 - SPI flash boot.
  • E8, E9 - power.
  • E10 - RTC power.
  • E11, E12, E13, E14 - CAN bus VCC and GND.
  • E15 - force PCIe to mPCIe.


Default state:

  • Jumpers E8, E9, E10, E11, E12, E13 and E14 are populated;
  • Jumpers E1, E2, E3, E4, E5, E6 and E15 are removed.