Difference between revisions of "UCM-iMX8M-Mini: Yocto Linux: Manual Installation: SD card"

From Compulab Mediawiki
Jump to: navigation, search
imported>Igor.vaisbein
(Run Yocto Linux image)
imported>Kirill.kapranov
(Installation)
Line 8: Line 8:
 
* Download the UCM-iMX8M-Mini Yocto Linux package from [https://www.compulab.com/products/computer-on-modules/ucm-imx8m-mini-nxp-i-mx-8m-mini-som-system-on-module-computer/#devres CompuLab website].
 
* Download the UCM-iMX8M-Mini Yocto Linux package from [https://www.compulab.com/products/computer-on-modules/ucm-imx8m-mini-nxp-i-mx-8m-mini-som-system-on-module-computer/#devres CompuLab website].
 
* Unzip the package to a directory on the host workstation.
 
* Unzip the package to a directory on the host workstation.
* The Yocto Linux SD-card image file mentioned below can be found in the {{filename|images}} subdirectory.  
+
* The Yocto Linux SD-card image file, mentioned below, can be found in the {{filename|images}} subdirectory.  
 
* Plug the USB SD Card reader into the host PC. Insert the micro-SD Card into the USB Card reader. From now we assume the device name of the MMC/SD card on your Linux PC is {{filename|/dev/sdX}}.
 
* Plug the USB SD Card reader into the host PC. Insert the micro-SD Card into the USB Card reader. From now we assume the device name of the MMC/SD card on your Linux PC is {{filename|/dev/sdX}}.
  
 
== Installation ==
 
== Installation ==
 
* Flash the image file to the micro-SD card:
 
* Flash the image file to the micro-SD card:
<pre>bzcat ~/path/to/ucm-imx8m-mini-yocto-linux/images/image-ucm-imx8m-mini.sdcard.bz2 | sudo dd of=/dev/sdX bs=1M
+
<pre>bzcat ~/path/to/ucm-imx8m-mini-yocto-linux/images/ucm-imx8m-mini.sdcard.bz2 | sudo dd of=/dev/sdX bs=1M
 
</pre>
 
</pre>
  

Revision as of 19:26, 21 May 2019

Introduction

This article provides instructions needed to install the Yocto Linux SD-card image on SD card using a Linux Host workstation. The image provides full boot system including U-Boot, Linux kernel, device driver modules and example root filesystem.

Preparation steps

  • Obtain a Linux PC workstation.
  • Obtain a USB Card reader and an micro-SD Card. Any commercially available micro-SD card of 1GB (or larger) may be used for the installation.
  • Download the UCM-iMX8M-Mini Yocto Linux package from CompuLab website.
  • Unzip the package to a directory on the host workstation.
  • The Yocto Linux SD-card image file, mentioned below, can be found in the images subdirectory.
  • Plug the USB SD Card reader into the host PC. Insert the micro-SD Card into the USB Card reader. From now we assume the device name of the MMC/SD card on your Linux PC is /dev/sdX.

Installation

  • Flash the image file to the micro-SD card:
bzcat ~/path/to/ucm-imx8m-mini-yocto-linux/images/ucm-imx8m-mini.sdcard.bz2 | sudo dd of=/dev/sdX bs=1M

Run Yocto Linux image

  • Insert the micro-SD card into SD socket P23 [see drawing]
  • Assemble jumper E15 in order to force the system to boot from SD card [see drawing]
  • Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector P13. [see drawing]
    Use a terminal emulator as described here
  • Power on the system.
  • When U-Boot starts press any key to stop autoboot.
  • Set the correct U-Boot environment in the U-Boot prompt:
env default -a
setenv fdt_file ucm-imx8m-mini.dtb
saveenv
  • Reboot the device:
reset
  • The system will boot into Linux.