Difference between revisions of "CM-T43: Evaluation Kit: Getting Started"
| Line 1: | Line 1: | ||
[[Image:CM-T43-eval-kit-quick-setup.jpg|800px]] | [[Image:CM-T43-eval-kit-quick-setup.jpg|800px]] | ||
[[Image:SB_SOM_topview2.jpg|thumb|right|alt=SB-SOM top view|<div align="center">SB-SOM top view</div>]] | [[Image:SB_SOM_topview2.jpg|thumb|right|alt=SB-SOM top view|<div align="center">SB-SOM top view</div>]] | ||
| − | |||
= System setup = | = System setup = | ||
| Line 9: | Line 8: | ||
# Connect the standard USB cable (included) between your host PC and the evaluation kit micro-USB2.0 connector <!-- [[SB-SOM:_Connectors:_P7|P7]] --> '''P7'''. | # Connect the standard USB cable (included) between your host PC and the evaluation kit micro-USB2.0 connector <!-- [[SB-SOM:_Connectors:_P7|P7]] --> '''P7'''. | ||
# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings: 115200 baud rate, 8 data bits, 1 stop bit, no parity, no flow control. | # On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings: 115200 baud rate, 8 data bits, 1 stop bit, no parity, no flow control. | ||
| + | |||
| + | [[Image:SB_SOM_bottomview2.jpg|thumb|right|alt=SB-SOM bottom view|<div align="center">SB-SOM bottom view</div>]] | ||
= Starting the system = | = Starting the system = | ||
| Line 21: | Line 22: | ||
*[[CM-T43 TI AM437x Linux|CM-T43 Linux guide]] | *[[CM-T43 TI AM437x Linux|CM-T43 Linux guide]] | ||
*[[CM-T43 TI AM437x Yocto Linux|CM-T43 Yocto guide]] | *[[CM-T43 TI AM437x Yocto Linux|CM-T43 Yocto guide]] | ||
| + | *[[CM-T43: Evaluation Kit: Hardware Guide|CM-T43 evaluation kit hardware guide]] | ||
*[http://www.compulab.co.il/products/computer-on-modules/cm-t43/#devres CM-T43 development resources] | *[http://www.compulab.co.il/products/computer-on-modules/cm-t43/#devres CM-T43 development resources] | ||
| − | |||
| − | |||
| − | |||
[[Category:SB-SOM]] | [[Category:SB-SOM]] | ||
[[Category:CM-T43]] | [[Category:CM-T43]] | ||
Revision as of 15:51, 8 May 2016
System setup
CM-T43 evaluation kit contains an SD card preloaded with Debian Linux image for CM-T43.
- Insert the evaluation kit SD card into the SD/MMC/SDIO socket P9 until you hear a clicking sound.
- Make sure jumpers E3 and E1 are not populated (default state).
- Connect the standard USB cable (included) between your host PC and the evaluation kit micro-USB2.0 connector P7.
- On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings: 115200 baud rate, 8 data bits, 1 stop bit, no parity, no flow control.
Starting the system
- Connect the DC 12V power supply adapter (included) to J6.
- Follow the messages in your terminal emulator program until you see the linux login prompt.
- NOTE: in case no messages appear in your terminal emulation program, please refer to the detailed USB console guide.
- Use the credentials below to login.
- username: root
- password: 111111
