Difference between revisions of "CM-X300: WinCE: Getting Started"

From Compulab Mediawiki
Jump to: navigation, search
m (1 revision(s))
 
Line 72: Line 72:
 
* [[CM-X300: WinCE: Configuring Eboot|Configuring Eboot]]
 
* [[CM-X300: WinCE: Configuring Eboot|Configuring Eboot]]
 
* [[WinCE: Application Development|Windows CE Application Development for CM-X300 modules]]
 
* [[WinCE: Application Development|Windows CE Application Development for CM-X300 modules]]
* [[CM-X300: WinCE6.0: Demo Image]]
+
* [[CM-X300: WinCE: Demo Image]]
 
* [[WinCE: OSDesign Development | Windows CE OSDesign Development]]
 
* [[WinCE: OSDesign Development | Windows CE OSDesign Development]]
 
* [[U-Boot for CM-X300]]
 
* [[U-Boot for CM-X300]]

Latest revision as of 10:00, 8 March 2010

Preparation steps

Admolition note.png Windows CE may be installed on CM-X300 using either a USB flash drive or a network connection. USB flash drive installation is the preferred method
  • Obtain a PC workstation with a serial communication port.
  • For networked installation, install a TFTP server on the host PC. For Windows machines we recommend using TFTPD32.
  • Download the Windows CE Demo package for CM-X300 from CompuLab website. Unzip the package to a directory on the host PC.
  • All image files mentioned below can be found in the ImageFiles folder.
  • Copy the contents of folder corresponding to the CM-X300 hardware configuration to a USB flash drive or to the folder exported by the TFTP server.
    • CPU stepping is identified according to the CM-X300 part number:
    - C624 corresponds to PXA300
    - C624M corresponds to PXA310

Image installation

Admolition warning.png Do not reset or power off the CM-X300 during the installation process! Doing so may result in a disabled module!
  • Connect the host PC to the CM-X300 via the serial cable supplied with the evaluation kit.
  • Start a terminal emulation software on the host PC. Refer to Setting up a console for settings.
  • Turn on the CM-X300 system. The U-Boot (initial boot-loader) will start with a command prompt.
Admolition note.png If the boot settings of the CM-X300 are different from default, press and hold ^C while turning on the CM-X300 in order to get command prompt.

Installation with a USB flash drive

  • Ensure that the files wince_updater.nb0, update.img, nk.bin, eboot.nb0 and, optionally, script.xml are present in the root directory of the USB flash drive.
  • Connect the USB flash drive to USB2 (host/slave) port of the CM-X300 platform.
  • Use the following U-Boot command to boot the Windows CE installer:
> run ce_setup

Installation with TFTP

  • Connect CM-X300 Ethernet port to the local Ethernet network
  • Ensure that the files wince_updater.nb0, update.img, nk.bin, eboot.nb0 and, optionally, script.xml are accessible by the TFTP server.
- TFTPD32 users: copy the files mentioned above to a folder and point the TFTP server to that folder.
  • Use U-Boot dhcp command to obtain an IP address or manually set the ipaddr environment variable:
> setenv ipaddr <CM-X300 ip address>
  • Set the serverip environment variable and save the new environment to NAND flash:
> setenv serverip <host ip address>
> saveenv
  • Use the following U-Boot command to boot the Windows CE installer:
> tftp 80400000 update.img && autoscr 80400000

Burning the image to NAND

  • CM-X300 Updater application will be started automatically after Windows CE installer boot is complete. The following screen will be displayed:
    - X300-Updater-start-screen.jpg
  • The CM-X300 Updater will point to the \Hard Disk\NK.bin file, located on a USB flash disk.
  • Uncheck the Quick Format check box to request a full low-level format of the CM-X300 NAND Flash.
    - A full low level format of the NAND Flash takes several minutes
  • Press the Start button
  • The update process takes several minutes.
X300-updater-Formatting.jpg CM-X300 Updating.jpg
  • After the update is completed, the CM-X300 Updater will display the following notification.
    - X300-Updater-finished.jpg
  • Press OK.

Post Installation

  • Windows CE boots automatically when the CM-X300 is power cycled or reset.
  • The following screen appears when the CM-X300 is up and running:
    - CM-X300-Home-Screen.jpg

See also