CM-X300: Linux: Debian
The example run-time Linux filesystem image for CM-X300 is based on Debian GNU/Linux Sid. The CompuLab Linux package for CM-X300 includes ready to run NAND flash image, Linux kernel configuration and source code patches, and an archive of the root filesystem the UBI image was created from.
The default Debian Sid Linux image includes more than 400 software packages. Among them:
- Core system
- Debian package management system
- X11 Windowing System
- Enlightenment desktop manager
- Netsurf web browser
- Samba connectivity suite
- SSH and FTP server and client
- ALSA configuration and usage utilities
- Bluetooth tools and daemons
The Getting started with Linux on CM-X300 page provides a brief introduction on how to install the run-time Linux image. This article describes package structure and peripheral device options specific to the CM-X300.
CM-X300 specific settings
Connection and Logging In
Use the following usernames and passwords to login:
Account with administrative privileges:
User: root Password: 111111
Regular user account:
User: user Password: 111111
In addition to these accounts CM-X300 allows anonymous FTP access. To login into the Linux system, you may use a serial console (ttyS2) at 38400 bps, or connect through the network, or use a keyboard and LCD display (tty1, tty2, tty3).
To configure networking, edit /etc/network/interfaces, /etc/resolv.conf, and /etc/hostname. For more information about Debian Linux network configuration read Network configuration chapter in the Debian Reference.
Linux file system image is designed to suit different kernel versions and configurations. Therefore, during the operating system startup, consoles at several serial ports and VGA display are enabled. Some of these devices may not be supported either because of kernel versions incompatibilities or because the kernel was not configured to support these devices. When the console is enabled at such device the following or similar message will appear on active console: INIT: Id "T0" respawning too fast: disabled for 5 minutes This is not an error message, it is just a warning that can be eliminated by editing /etc/inittab file.
X Windows system
CompuLab package contains full featured X Windows system with Enlightment window manager. Before starting X Windows, connect USB mouse and keyboard to the system. You can run X Windows by typing startx.
Audio and Touchscreen
CM-X300 uses WM9715 (Wolfson) AC97 codec with integrated touchscreen controller. Both audio and touchscreen drivers are modularized if you use default CM-X300 configuration. The following commands enable audio support:
modprobe snd-soc-em-x270 modprobe snd-soc-wm9712 modprobe snd-soc-pxa2xx
The following command enables touchscreen support:
Enabling touchscreen driver without AC97 controller driver is meaningless, since wm97xx-ts driver uses AC97 bus to access the touchscreen device.
Note, that the same codec and driver is used on Compulab EM-X270 module. More information about Linux audio subsystem can be found at ALSA project official website.
Touchscreen calibration can be performed with ts_calibrate utility. To calibrate the touchscreen:
- Make sure X Server is not running
- Load touchscreen driver as described in Audio and Touchscreen section
- Set the TSLIB_TSDEVICE system variable:
cd /sys/class/input name="" for tsdir in *; do if [ -f $tsdir/name ] ; then name=`cat $tsdir/name` fi; echo $name | grep -i "touchscreen" >& /dev/null if [ $? -eq 0 ] ; then name=`ls -1 $tsdir | grep event\[0-9\] | grep -v :` break; fi; done; export TSLIB_TSDEVICE=/dev/input/$name
- Run ts_calibrate utility:
For proper calibration you are required to touch the touchscreen corners and center in the following order: top-left, top-right, bottom-right, bottom-left, center. The calibration results are saved to file /etc/pointercal.
Wireless LAN support
CompuLab Debian Linux package supports wireless LAN on CM-X300 modules.
The firmware for the wireless LAN controller is included in the filesystem image and can be found at /lib/firmware directory.
Typical use of those utilities:
- Enable the wireless interface (eth1):
ifconfig eth1 up
- Check for available access points around:
iwlist eth1 scan
- Assign an access point:
iwconfig eth1 essid "My Network"
- Get an IP address from the access point:
To mount the memory card, monitor /proc/partitions to see what partitions were detected on the MMC/SD card. Next, if there's an appropriate device node in /dev, you can directly mount it; otherwise you should create the device node first. For example, suppose the MMC/SD partition you want to mount is mmcblk0p1, then use the following command:
if [ ! -b /dev/mmcblk0p1 ]; then mknod /dev/mmcblk0p1 b 253 1; fi mount /dev/mmcblk0p1 /mnt/mmc
The demo keypad that is provided in the evaluation kit can be interfaced with via the /dev/input/event0 device file.
Boot time optimization for JFFS2 users
The JFFS2 Debian image for CM-X300 boot takes relatively much time. The delays during the boot are partially related to JFFS2 mount time and partially to Debian image configuration.
JFFS2 designed for robust operation in embedded environment where sudden power interruptions are frequent. As a trade off for reliability in this situations, JFFS2 has long mount time. The mount time scales linearly with flash partition size. To speed up the boot process you can partition the NAND flash so it'll contain relatively small partition holding root filesystem and another partition(s) for applications and data. Mounting of applications and data partitions can be done in the background concurrently with init scripts execution.
Another reason for slow boot is Debian configuration. We tried to make the Debian image for CM-X300 as generic as possible. Therefore it contains a lot of services that may not be required for your application. Removing the unneeded services will reduce the boot time. Also, we have not modified default Debian scripts to allow better system updatability. Because of it, one of the init scripts remounts and checks the root file system several times. You can amend /etc/init.d/checkroot.sh to skip root filesystem remounts and checks.