Difference between revisions of "Getting started with Linux on CM-X300"

From Compulab Mediawiki
Jump to: navigation, search
(In some cases nfs timeouts using udp. Thus the suggestion to mount using tcp.)
(→‎Installation using NFS)
Line 5: Line 5:
 
* Download the [http://www.compulab.co.il/x300/download/x300-linux.zip Linux distribution package for CM-X300] from CompuLab's website . Unzip the package to a directory on your host workstation.
 
* Download the [http://www.compulab.co.il/x300/download/x300-linux.zip Linux distribution package for CM-X300] from CompuLab's website . Unzip the package to a directory on your host workstation.
 
* All image files mentioned below can be found in {{filename|images}} subdirectory
 
* All image files mentioned below can be found in {{filename|images}} subdirectory
−
* Copy {{filename|debian-image.jffs2}} and {{filename|cm-x300-kernel.jffs2}} from [http://www.compulab.co.il/x300/download/x300-linux.zip Linux distribution package for CM-X300] either to a directory exported through NFS or to a USB flash drive.
+
* Copy {{filename|debian-image.ubi}} and {{filename|cm-x300-kernel.jffs2}} from [http://www.compulab.co.il/x300/download/x300-linux.zip Linux distribution package for CM-X300] either to a directory exported through NFS or to a USB flash drive.
  
 
== Image installation ==
 
== Image installation ==
Line 18: Line 18:
 
*: - On Windows machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|first_boot.img}} to the same folder and point the TFTP server to that folder
 
*: - On Windows machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|first_boot.img}} to the same folder and point the TFTP server to that folder
 
*: - On Linux machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|first_boot.img}} to TFTP sevrver root directory, usually {{filename|/tftpboot}} or {{filename|/tftproot}}.
 
*: - On Linux machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|first_boot.img}} to TFTP sevrver root directory, usually {{filename|/tftpboot}} or {{filename|/tftproot}}.
−
* You can use U-boot {{cmd|dhcp}} command to obtain IP address or manually set {{parameter|ipaddr}} and {{parameter|serverip}} environment variables:
+
* You can use U-boot {{cmd|dhcp}} command to obtain IP address or manually set {{parameter|ipaddr}} environment variable:
 +
<pre>
 +
> setenv ipaddr <CM-X300 ip address>
 +
</pre>
 +
* Set {{parameter|serverip}} environment variable and save the new environment to NAND flash:
 
<pre>
 
<pre>
 
> setenv serverip <host ip address>
 
> setenv serverip <host ip address>
−
> setenv ipaddr <CM-X300 ip address>
 
 
> saveenv
 
> saveenv
 
</pre>
 
</pre>
Line 34: Line 37:
 
</pre>  
 
</pre>  
 
* After the ramdisk image is loaded you will get Linux login prompt. Login as {{parameter|root}} into the system.
 
* After the ramdisk image is loaded you will get Linux login prompt. Login as {{parameter|root}} into the system.
−
* Mount the NFS share containing {{filename|cm-x300-kernel.jffs2}} and {{filename|debian-image.jffs2}} image:
+
* Mount the NFS share containing {{filename|cm-x300-kernel.jffs2}} and {{filename|debian-image.ubi}} image:
 
<pre>
 
<pre>
 
$ mount <host ip>:/path/to/nfs/share /mnt/net
 
$ mount <host ip>:/path/to/nfs/share /mnt/net
−
or
 
−
$ mount -o tcp <host ip>:/path/to/nfs/share /mnt/net
 
 
</pre>  
 
</pre>  
 
* Format the NAND flash kernel partition and write the kernel image onto it:
 
* Format the NAND flash kernel partition and write the kernel image onto it:
Line 47: Line 48:
 
* Format the NAND flash root filesystem partition and write Debian filesystem image onto it:
 
* Format the NAND flash root filesystem partition and write Debian filesystem image onto it:
 
<pre>
 
<pre>
−
$ flash_eraseall /dev/mtd5
+
$ ubiformat /dev/mtd5 -f /mnt/net/debian-image.ubi
−
$ ubiattach /dev/ubi_ctrl -m 5 -O 2048
 
−
$ ubimkvol /dev/ubi0 -m -N <new filesystem name>
 
−
$ ubiupdatevol /dev/ubi0_0 /mnt/net/debian-image.jffs2
 
 
</pre>
 
</pre>
  
 
=== Installation using USB flash drive ===
 
=== Installation using USB flash drive ===
 
* Make sure that CM-X300's ETH0 port is '''disconnected'''
 
* Make sure that CM-X300's ETH0 port is '''disconnected'''
−
* Make sure that Linux kernel binary image {{filename|kernel.img}}, ramdisk image {{filename|ramdisk.img}}, kernel JFFS2 image {{filename|cm-x300-kernel.jffs2}}, Debian filesystem JFFS2 image {{filename|debian-image.jffs2}} and bootloader script image {{filename|first_boot.img}} are present at the root directory of the USB flash drive.  
+
* Make sure that Linux kernel binary image {{filename|kernel.img}}, ramdisk image {{filename|ramdisk.img}}, kernel JFFS2 image {{filename|cm-x300-kernel.jffs2}}, Debian filesystem JFFS2 image {{filename|debian-image.ubi}} and bootloader script image {{filename|first_boot.img}} are present at the root directory of the USB flash drive.  
 
* Connect USB flash drive to CM-X300. Use USB2 (host/slave) port.  
 
* Connect USB flash drive to CM-X300. Use USB2 (host/slave) port.  
 
* Use the following U-boot command to boot Linux on CM-X300:
 
* Use the following U-boot command to boot Linux on CM-X300:
Line 72: Line 70:
 
* Format the NAND flash root filesystem partition and write Debian filesystem image onto it:
 
* Format the NAND flash root filesystem partition and write Debian filesystem image onto it:
 
<pre>
 
<pre>
−
$ flash_eraseall /dev/mtd5
+
$ ubiformat /dev/mtd5 -f /media/sda1/debian-image.ubi
−
$ ubiattach /dev/ubi_ctrl -m 5 -O 2048
 
−
$ ubimkvol /dev/ubi0 -m -N <new filesystem name>
 
−
$ ubiupdatevol /dev/ubi0_0 /media/sda1/debian-image.jffs2
 
 
</pre>
 
</pre>
  
Line 119: Line 114:
 
* [[Linux Kernel for CM-X300]]
 
* [[Linux Kernel for CM-X300]]
 
* [[Debian Linux for CM-X300]]
 
* [[Debian Linux for CM-X300]]
 +
* [[U-Boot for CM-X300]]

Revision as of 14:17, 22 November 2009

Preparation steps

Admolition note.png It is possible to install Linux on CM-X300 using either an NFS share or a USB flash drive. The first method is preferred because NFS setup will ease further Linux evaluation and development.
  • Obtain a PC workstation with serial communication port.
  • For installation using NFS install TFTP server on host PC. For Windows machines we recommend TFTPD32 included in this distribution package.
  • Download the Linux distribution package for CM-X300 from CompuLab's website . Unzip the package to a directory on your host workstation.
  • All image files mentioned below can be found in images subdirectory
  • Copy debian-image.ubi and cm-x300-kernel.jffs2 from Linux distribution package for CM-X300 either to a directory exported through NFS or to a USB flash drive.

Image installation

  • Connect the host PC to the CM-X300 via a null modem cable supplied with the Eval Kit.
  • Start terminal emulation software on your PC using the COM port to which the null modem is connected. Set baud rate to 38400 bps, 8 bit per frame, 1 stop bit, no parity, no flow control.
  • Turn on the CM-X300. The U-Boot will start and you will get a command prompt.
Admolition note.png If the boot settings of your CM-X300 are different than default, you may need to press and hold ^C while turning the CM-X300 on, in order to get command prompt.

Installation using NFS

  • Connect CM-X300's ETH0 port to your local Ethernet
  • Make sure that Linux kernel binary image kernel.img, ramdisk image ramdisk.img and bootloader script image first_boot.img are accessible by the TFTP server.
    - On Windows machine: copy kernel.img, ramdisk.img and first_boot.img to the same folder and point the TFTP server to that folder
    - On Linux machine: copy kernel.img, ramdisk.img and first_boot.img to TFTP sevrver root directory, usually /tftpboot or /tftproot.
  • You can use U-boot dhcp command to obtain IP address or manually set ipaddr environment variable:
> setenv ipaddr <CM-X300 ip address>
  • Set serverip environment variable and save the new environment to NAND flash:
> setenv serverip <host ip address>
> saveenv
  • Use the following U-boot command to boot Linux on CM-X300:
> tftp 80400000 first_boot.img && autoscr 80400000
  • During boot the CM-X300 tries to obtain an IP address using DHCP. If you do not have DHCP server you can set the CM-X300 IP address statically using ifconfig:
$ ifconfig eth0 <ip address>
  • After the ramdisk image is loaded you will get Linux login prompt. Login as root into the system.
  • Mount the NFS share containing cm-x300-kernel.jffs2 and debian-image.ubi image:
$ mount <host ip>:/path/to/nfs/share /mnt/net
  • Format the NAND flash kernel partition and write the kernel image onto it:
$ flash_eraseall /dev/mtd4
$ nandwrite /dev/mtd4 /mnt/net/cm-x300-kernel.jffs2
  • Format the NAND flash root filesystem partition and write Debian filesystem image onto it:
$ ubiformat /dev/mtd5 -f /mnt/net/debian-image.ubi

Installation using USB flash drive

  • Make sure that CM-X300's ETH0 port is disconnected
  • Make sure that Linux kernel binary image kernel.img, ramdisk image ramdisk.img, kernel JFFS2 image cm-x300-kernel.jffs2, Debian filesystem JFFS2 image debian-image.ubi and bootloader script image first_boot.img are present at the root directory of the USB flash drive.
  • Connect USB flash drive to CM-X300. Use USB2 (host/slave) port.
  • Use the following U-boot command to boot Linux on CM-X300:
> usb start
> fatload usb 0:1 80400000 first_boot.img
> autoscr 80400000
  • After the ramdisk image is loaded you will get Linux login prompt. Login as root into the system.
  • The USB flash drive will be automatically mounted under /media/sda1
  • Format the NAND flash kernel partition and write the kernel image onto it:
$ flash_eraseall /dev/mtd4
$ nandwrite /dev/mtd4 /media/sda1/cm-x300-kernel.jffs2
  • Format the NAND flash root filesystem partition and write Debian filesystem image onto it:
$ ubiformat /dev/mtd5 -f /media/sda1/debian-image.ubi

After Installation

  1. Reset the CM-X300.
    2. Admolition note.png If the boot settings of your CM-X300 are different than default, you may need to press and hold ^C while turning the CM-X300 on, in order to get command prompt.
  2. To start Linux type: 
    > fsload; bootm
  3. If you want Linux to start automatically, type: 
    > setenv bootdelay <delay in seconds> 
> setenv bootcmd "fsload; bootm"
> saveenv
> boot

If you want to get back to U-Boot prompt, hold Ctrl-C during reset.

Connection and Logging In

Use the following usernames and passwords to login:

Account with administrative privileges: 

User: root
Password: 111111

Regular user account: 

User: user
Password: 111111

In addition to these accounts CM-X300 allows anonymous FTP access.

See also

Retrieved from "https://mediawiki.compulab.com/w/index.php?title=Getting_started_with_Linux_on_CM-X300&oldid=400"